问题
I have a very large set of data (~3 million records) which needs to be merged with updates and new records on a daily schedule. I have a stored procedure that actually breaks up the record set into 1000 record chunks and uses the MERGE command with temp tables in an attempt to avoid locking the live table while the data is updating. The problem is that it doesn't exactly help. The table still "locks up" and our website that uses the data receives timeouts when attempting to access the data. I even tried splitting it up into 100 record chunks and even tried a WAITFOR DELAY '000:00:5' to see if it would help to pause between merging the chunks. It's still rather sluggish.
I'm looking for any suggestions, best practices, or examples on how to merge large sets of data without locking the tables.
Thanks
回答1:
Change your front end to use NOLOCK or READ UNCOMMITTED when doing the selects.
You can't NOLOCK MERGE,INSERT, or UPDATE as the records must be locked in order to perform the update. However, you can NOLOCK the SELECTS.
Note that you should use this with caution. If dirty reads are okay, then go ahead. However, if the reads require the updated data then you need to go down a different path and figure out exactly why merging 3M records is causing an issue.
I'd be willing to bet that most of the time is spent reading data from the disk during the merge command and/or working around low memory situations. You might be better off simply stuffing more ram into your database server.
An ideal amount would be to have enough ram to pull the whole database into memory as needed. For example, if you have a 4GB database, then make sure you have 8GB of RAM.. in an x64 server of course.
回答2:
I'm afraid that I've quite the opposite experience. We were performing updates and insertions where the source table had only a fraction of the number of rows as the target table, which was in the millions.
When we combined the source table records across the entire operational window and then performed the MERGE just once, we saw a 500% increase in performance. My explanation for this is that you are paying for the up front analysis of the MERGE command just once instead of over and over again in a tight loop.
Furthermore, I am certain that merging 1.6 million rows (source) into 7 million rows (target), as opposed to 400 rows into 7 million rows over 4000 distinct operations (in our case) leverages the capabilities of the SQL server engine much better. Again, a fair amount of the work is in the analysis of the two data sets and this is done only once.
Another question I have to ask is well is whether you are aware that the MERGE command performs much better with indexes on both the source and target tables? I would like to refer you to the following link:
http://msdn.microsoft.com/en-us/library/cc879317(v=SQL.100).aspx
回答3:
From personal experience, the main problem with MERGE is that since it does page lock it precludes any concurrency in your INSERTs directed to a table. So if you go down this road it is fundamental that you batch all updates that will hit a table in a single writer.
For example: we had a table on which INSERT took a crazy 0.2 seconds per entry, most of this time seemingly being wasted on transaction latching, so we switched this over to using MERGE and some quick tests showed that it allowed us to insert 256 entries in 0.4 seconds or even 512 in 0.5 seconds, we tested this with load generators and all seemed to be fine, until it hit production and everything blocked to hell on the page locks, resulting in a much lower total throughput than with the individual INSERTs.
The solution was to not only batch the entries from a single producer in a MERGE operation, but also to batch the batch from producers going to individual DB in a single MERGE operation through an additional level of queue (previously also a single connection per DB, but using MARS to interleave all the producers call to the stored procedure doing the actual MERGE transaction), this way we were then able to handle many thousands of INSERTs per second without problem.
Having the NOLOCK hints on all of your front-end reads is an absolute must, always.
来源：https://stackoverflow.com/questions/3294234/sql-server-merging-large-tables-without-locking-the-data