Kubernetes pod cannot mount iSCSI volume: failed to get any path for iscsi disk

自闭症网瘾萝莉.ら 提交于 2021-02-10 14:42:41

问题


I would like to add an iSCSI volume to a pod as in this this example. I have already prepared an iSCSI target on a Debian server and installed open-iscsi on all my worker nodes. I have also confirmed that I can mount the iSCSI target on a worker node with command line tools (i.e. still outside Kubernetes). This works fine. For simplicity, there is no authentication (CHAP) in play yet, and there is already a ext4 file system present on the target.

I would now like for Kubernetes 1.14 to mount the same iSCSI target into a pod with the following manifest:

---
apiVersion: v1
kind: Pod
metadata:
  name: iscsipd
spec:
  containers:
  - name: iscsipd-ro
    image: kubernetes/pause
    volumeMounts:
    - mountPath: "/mnt/iscsipd"
      name: iscsivol
  volumes:
  - name: iscsivol
    iscsi:
      targetPortal: 1.2.3.4 # my target
      iqn: iqn.2019-04.my-domain.com:lun1
      lun: 0
      fsType: ext4
      readOnly: true

According to kubectl describe pod this works in the initial phase (SuccessfulAttachVolume), but then fails (FailedMount). The exact error message reads:

Warning  FailedMount ... Unable to mount volumes for pod "iscsipd_default(...)": timeout expired waiting for volumes to attach or mount for pod "default"/"iscsipd". list of unmounted volumes=[iscsivol]. list of unattached volumes=[iscsivol default-token-7bxnn]
Warning  FailedMount ... MountVolume.WaitForAttach failed for volume "iscsivol" : failed to get any path for iscsi disk, last err seen:
Could not attach disk: Timeout after 10s

How can I further diagnose and overcome this problem?

UPDATE In this related issue the solution consisted of using a numeric IP address for the target. However, this does not help in my case, since I am already using a targetPortal of the form 1.2.3.4 (have also tried both with and without port number 3260).

UPDATE Stopping scsid.service and/or open-iscsi.service (as suggested here) did not make a difference either.

UPDATE The error apparently gets triggered in pkg/volume/iscsi/iscsi_util.go if waitForPathToExist(&devicePath, multipathDeviceTimeout, iscsiTransport) fails. However, what is strange is that when it is triggered the file at devicePath (/dev/disk/by-path/ip-...-iscsi-...-lun-...) does actually exist on the node.

UPDATE I have used this procedure for defining an simple iSCSI target for these test purposes:

pvcreate /dev/sdb
vgcreate iscsi /dev/sdb
lvcreate -L 10G -n iscsi_1 iscsi
apt-get install tgt
cat >/etc/tgt/conf.d/iscsi_1.conf <<EOL
<target iqn.2019-04.my-domain.com:lun1>
  backing-store /dev/mapper/iscsi-iscsi_1
  initiator-address 5.6.7.8 # my cluster node #1
  ... # my cluster node #2, etc.
</target>
EOL
systemctl restart tgt
tgtadm --mode target --op show

回答1:


This is probably because of authentication issue to your iscsi target.

If you don't use CHAP authentication yet, you still have to disable authentication. For example, if you use targetcli, you can run below commands to disable it.

$ sudo targetcli
/> /iscsi/iqn.2003-01.org.xxxx/tpg1 set attribute authentication=0 # will disable auth
/> /iscsi/iqn.2003-01.org.xxxx/tpg1 set attribute generate_node_acls=1 # will force to use tpg1 auth mode by default

If this doesn't help you, please share your iscsi target configuration, or guide that you followed.




回答2:


this worked for me

iscsi:
     chapAuthSession: false

References:

  1. https://github.com/kubernetes-retired/external-storage/tree/master/iscsi/targetd
  2. https://docs.mirantis.com/docker-enterprise/v3.1/dockeree-products/mke/deploy-apps-with-kubernetes/persistent-storage/configure-iscsi.html


来源:https://stackoverflow.com/questions/55920173/kubernetes-pod-cannot-mount-iscsi-volume-failed-to-get-any-path-for-iscsi-disk

标签
易学教程内所有资源均来自网络或用户发布的内容,如有违反法律规定的内容欢迎反馈
该文章没有解决你所遇到的问题?点击提问,说说你的问题,让更多的人一起探讨吧!