Getting PEAR to work on XAMPP (Apache/MySQL stack on Windows)

问题

I'm trying to install Laconica, an open-source Microblogging application on my Windows development server using XAMPP as per the instructions provided.

The website cannot find PEAR, and throws the below errors:

Warning: require_once(PEAR.php) [function.require-once]: failed to open stream: No such file or directory in C:\xampplite\htdocs\laconica\lib\common.php on line 31

Fatal error: require_once() [function.require]: Failed opening required 'PEAR.php' (include_path='.;\xampplite\php\pear\PEAR') in C:\xampplite\htdocs\laconica\lib\common.php on line 31

PEAR is located in C:\xampplite\php\pear
phpinfo() shows me that the include path is .;\xampplite\php\pear

What am I doing wrong? Why isn't the PEAR folder being included?

回答1:

You need to fix your include_path system variable to point to the correct location.

To fix it edit the php.ini file. In that file you will find a line that says, "include_path = ...". (You can find out what the location of php.ini by running phpinfo() on a page.) Fix the part of the line that says, "\xampplite\php\pear\PEAR" to read "C:\xampplite\php\pear". Make sure to leave the semi-colons before and/or after the line in place.

Restart PHP and you should be good to go. To restart PHP in IIS you can restart the application pool assigned to your site or, better yet, restart IIS all together.

回答2:

If you are using the portable XAMPP installation and Windows 7, and, like me have the version after they removed the XAMPP shell from the control panel none of the suggested answers here will do you much good as the packages will not install.

The problem is with the config file. I found the correct settings after a lot of trial and error.

Simply pull up a command window in the \xampp\php directory and run

pear config-set doc_dir :\xampp\php\docs\PEAR
pear config-set cfg_dir :\xampp\php\cfg
pear config-set data_dir :\xampp\php\data\PEAR
pear config-set test_dir :\xampp\php\tests
pear config-set www_dir :\xampp\php\www

you will want to replace the ':' with the actual drive letter that your portable drive is running on at the moment. Unfortunately, this needs to be done any time this drive letter changes, but it did get the module I needed installed.

回答3:

I tried all of the other answers first but none of them seemed to work so I set the pear path statically in the pear config file

C:\xampp\php\pear\Config.php

find this code:

if (!defined('PEAR_INSTALL_DIR') || !PEAR_INSTALL_DIR) {
    $PEAR_INSTALL_DIR = PHP_LIBDIR . DIRECTORY_SEPARATOR . 'pear';
} 
else {
    $PEAR_INSTALL_DIR = PEAR_INSTALL_DIR;
}

and just replace it with this:

$PEAR_INSTALL_DIR = "C:\\xampp\\php\\pear";

I restarted apache and used the command:

pear config-all

make sure the all of the paths no longer start with C:\php\pear

回答4:

AS per point 1, your PEAR path is c:\xampplite\php\pear\

However, your path is pointing to \xampplite\php\pear\PEAR

Putting the two one above the other you can clearly see one is too long:

c:\xampplite\php\pear\

\xampplite\php\pear\PEAR

Your include path is set to go one PEAR too deep into the pear tree. The PEAR subfolder of the pear folder includes the PEAR component. You need to adjust your include path up one level.

(you don't need the c: by the way, your path is fine as is, just too deep)

回答5:

Try adding the drive letter:

include_path='.;c:\xampplite\php\pear\PEAR'

also verify that PEAR.php is actually there, it might be in \php\ instead:

include_path='.;c:\xampplite\php'

回答6:

Another gotcha for this kind of problem: avoid running pear within a Unix shell (e.g., Git Bash or Cygwin) on a Windows machine. I had the same problem and the path fix suggested above didn't help. Switched over to a Windows shell, and the pear command works as expected.

回答7:

On Windows use the Xampp shell (there is a 'Shell' button in your XAMPP control panel)

then

cd php\pear

to go to 'C:\xampp\php\pear'

then type

pear

回答8:

I fixed

avast deletes your server.php in your directory so disable the antivirus

check the (server.php) file on your laravel folder

server.php

<?php

/**
 * Laravel - A PHP Framework For Web Artisans
 *
 * @package  Laravel
 * @author   Taylor Otwell <taylor@laravel.com>
 */

$uri = urldecode(
    parse_url($_SERVER['REQUEST_URI'], PHP_URL_PATH)
);

// This file allows us to emulate Apache's "mod_rewrite" functionality from the
// built-in PHP web server. This provides a convenient way to test a Laravel
// application without having installed a "real" web server software here.
if ($uri !== '/' && file_exists(__DIR__.'/public'.$uri)) {
    return false;
}

require_once __DIR__.'/public/index.php';

来源：https://stackoverflow.com/questions/62658/getting-pear-to-work-on-xampp-apache-mysql-stack-on-windows

标签

php

pear

laconica