python to arduino serial read & write

Question

I\'m trying to \"ping pong\" info back and forth between some python code and arduino code. I want to send two setpoints to the arduino code periodically (for instance on th

Answer 1

First you have to install a module call Serial. To do that go to the folder call Scripts which is located in python installed folder. If you are using Python 3 version it's normally located in location below,

C:\Python34\Scripts  

Once you open that folder right click on that folder with shift key. Then click on 'open command window here'. After that cmd will pop up. Write the below code in that cmd window,

pip install PySerial

and press enter.after that PySerial module will be installed. Remember to install the module u must have an INTERNET connection.

---

after successfully installed the module open python IDLE and write down the bellow code and run it.

import serial
# "COM11" is the port that your Arduino board is connected.set it to port that your are using        
ser = serial.Serial("COM11", 9600)
while True:
    cc=str(ser.readline())
    print(cc[2:][:-5])   

Answer 2

I found it is better to use the command Serial.readString() to replace the Serial.read() to obtain the continuous I/O for Arduino.

Answer 3

You shouldn't be closing the serial port in Python between writing and reading. There is a chance that the port is still closed when the Arduino responds, in which case the data will be lost.

while running:  
    # Serial write section
    setTempCar1 = 63
    setTempCar2 = 37
    setTemp1 = str(setTempCar1)
    setTemp2 = str(setTempCar2)
    print ("Python value sent: ")
    print (setTemp1)
    ard.write(setTemp1)
    time.sleep(6) # with the port open, the response will be buffered 
                  # so wait a bit longer for response here

    # Serial read section
    msg = ard.read(ard.inWaiting()) # read everything in the input buffer
    print ("Message from arduino: ")
    print (msg)

The Python Serial.read function only returns a single byte by default, so you need to either call it in a loop or wait for the data to be transmitted and then read the whole buffer.

On the Arduino side, you should consider what happens in your loop function when no data is available.

void loop()
{
  // serial read section
  while (Serial.available()) // this will be skipped if no data present, leading to
                             // the code sitting in the delay function below
  {
    delay(30);  //delay to allow buffer to fill 
    if (Serial.available() >0)
    {
      char c = Serial.read();  //gets one byte from serial buffer
      readString += c; //makes the string readString
    }
  }

Instead, wait at the start of the loop function until data arrives:

void loop()
{
  while (!Serial.available()) {} // wait for data to arrive
  // serial read section
  while (Serial.available())
  {
    // continue as before

EDIT 2

Here's what I get when interfacing with your Arduino app from Python:

>>> import serial
>>> s = serial.Serial('/dev/tty.usbmodem1411', 9600, timeout=5)
>>> s.write('2')
1
>>> s.readline()
'Arduino received: 2\r\n'

So that seems to be working fine.

In testing your Python script, it seems the problem is that the Arduino resets when you open the serial port (at least my Uno does), so you need to wait a few seconds for it to start up. You are also only reading a single line for the response, so I've fixed that in the code below also:

#!/usr/bin/python
import serial
import syslog
import time

#The following line is for serial over GPIO
port = '/dev/tty.usbmodem1411' # note I'm using Mac OS-X


ard = serial.Serial(port,9600,timeout=5)
time.sleep(2) # wait for Arduino

i = 0

while (i < 4):
    # Serial write section

    setTempCar1 = 63
    setTempCar2 = 37
    ard.flush()
    setTemp1 = str(setTempCar1)
    setTemp2 = str(setTempCar2)
    print ("Python value sent: ")
    print (setTemp1)
    ard.write(setTemp1)
    time.sleep(1) # I shortened this to match the new value in your Arduino code

    # Serial read section
    msg = ard.read(ard.inWaiting()) # read all characters in buffer
    print ("Message from arduino: ")
    print (msg)
    i = i + 1
else:
    print "Exiting"
exit()

Here's the output of the above now:

$ python ardser.py
Python value sent:
63
Message from arduino:
Arduino received: 63
Arduino sends: 1


Python value sent:
63
Message from arduino:
Arduino received: 63
Arduino sends: 1


Python value sent:
63
Message from arduino:
Arduino received: 63
Arduino sends: 1


Python value sent:
63
Message from arduino:
Arduino received: 63
Arduino sends: 1


Exiting