Linux join utility complains about input file not being sorted

问题

I have two files:

file1 has the format:

field1;field2;field3;field4

(file1 is initially unsorted)

file2 has the format:

field1

(file2 is sorted)

I run the 2 following commands:

sort -t\; -k1 file1 -o file1 # to sort file 1
join -t\; -1 1 -2 1 -o 1.1 1.2 1.3 1.4 file1 file2

I get the following message:

join: file1:27497: is not sorted: line_which_was_identified_as_out_of_order

Why is this happening ?

(I also tried to sort file1 taking into consideration the entire line not only the first filed of the line but with no success)

sort -t\; -c file1 doesn't output anything. Around line 27497, the situation is indeed strange which means that sort doesn't do its job correctly:

              XYZ113017;...
line 27497--> XYZ11301;...
              XYZ11301;...

回答1:

To complement Wumpus Q. Wumbley's helpful answer with a broader perspective (since I found this post researching a slightly different problem).

• When using join, the input files must be sorted by the join field ONLY, otherwise you may see the warning reported by the OP.

There are two common scenarios in which more than the field of interest is mistakenly included when sorting the input files:

• If you do specify a field, it's easy to forget that you must also specify a stop field - even if you target only 1 field - because sort uses the remainder of the line if only a start field is specified; e.g.:

  • sort -t, -k1 ... # !! FROM field 1 THROUGH THE REST OF THE LINE
  • sort -t, -k1,1 ... # Field 1 only

• If your sort field is the FIRST field in the input, it's tempting to not specify any field selector at all.

  • However, if field values can be prefix substrings of each other, sorting whole lines will NOT (necessarily) result in the same sort order as just sorting by the 1st field:
  • sort ... # NOT always the same as 'sort -k1,1'! see below for example

Pitfall example:

#!/usr/bin/env bash

# Input data: fields separated by '^'.
# Note that, when properly sorting by field 1, the order should
# be "nameA" before "nameAA" (followed by "nameZ").
# Note how "nameA" is a substring of "nameAA".
read -r -d '' input <<EOF
nameA^other1
nameAA^other2
nameZ^other3
EOF

# NOTE: "WRONG" below refers to deviation from the expected outcome
#       of sorting by field 1 only, based on mistaken assumptions.
#       The commands do work correctly in a technical sense.

echo '--- just sort'
sort <<<"$input" | head -1 # WRONG: 'nameAA' comes first

echo '--- sort FROM field 1'
sort -t^ -k1 <<<"$input" | head -1 # WRONG: 'nameAA' comes first

echo '--- sort with field 1 ONLY'
sort -t^ -k1,1 <<<"$input" | head -1 # ok, 'nameA' comes first

Explanation:

• When NOT limiting sorting to the first field, it is the relative sort order of chars. ^ and A (column index 6) that matters in this example. In other words: the field separator is compared to data, which is the source of the problem: ^ has a HIGHER ASCII value than A, and therefore sorts after 'A', resulting in the line starting with nameAA^ sorting BEFORE the one with nameA^.

• Note: It is possible for problems to surface on one platform, but be masked on another, based on locale and character-set settings and/or the sort implementation used; e.g., with a locale of en_US.UTF-8 in effect, with , as the separator and - permissible inside fields:

  • sort as used on OSX 10.10.2 (which is an old GNU sort version, 5.93) sorts , before - (in line with ASCII values)
  • sort as used on Ubuntu 14.04 (GNU sort 8.21) does the opposite: sorts - before ,^[1]

^{[1] I don't know why - if somebody knows, please tell me. Test with sort <<<$'-\n,'}

回答2:

sort -k1 uses all fields starting from field 1 as the key. You need to specify a stop field.

sort -t\; -k1,1

回答3:

... or the gnu sort is just as buggy as every other GNU command

try and sort Gi1/0/11 vs Gi1/0/1 and you'll never be able to get an actual regular textual sort suitable for join input because someone added some extra intelligence in sort which will happily use numeric or human numeric sorting automagically in such cases without even bothering to add a flag to force the regular behavior

what is suitable for humans is seldom suitable for scripting

来源：https://stackoverflow.com/questions/25431673/linux-join-utility-complains-about-input-file-not-being-sorted